SI 7336G-1TC Power supply, ECU module LED grey silicone adhesive

Product description

SI 7336G-1TC grey silicone adhesive is a neutral silicone sealing material that absorbs moisture in the air and cures at room temperature in one component.

It is non-corrosive to materials, and has good bonding and sealing performance for most plastic metals and other materials, protecting electronic products in a stable state under harsh conditions.

SI 7336G-1TC gray silicone adhesive after curing elastomer has the following characteristics:

SI 7336G-1TC has excellent non-corrosive adhesion to metals, including copper, plastics, ceramics, glass, etc., without the use of primer.

Excellent weather resistance, water resistance and chemical resistance

Resistance to moisture, dirt and other atmospheric components

Excellent electrical insulation properties.

High thermal conductivity bonding sealant

Stable mechanical and electrical properties between -60 and 250°C

Fields of Application

Power, solar energy, equipment, home, automotive, LED lighting,

Power supply, ECU module, semiconductor, high power transistor, thyristor diode

Any inquiry, welcome to contact us +86-18321208486

SI 7336G-1TC Power supply, ECU module LED grey silicone adhesive

Name: SI 7336G-1TC Power supply, ECU module LED grey silicone adhesive
Brand: Max Tech
Price: 5 USD
Availability: InStock

5,00 US$

Color

packing

Electronic Industry silicone sealant for for household appliance, engineering machinery, PV modules, (opcional)

0/500

Cantidad

Technical parameters before and after curing

Test items	Test standard	Unit	SI 7336G-1TC
Before cured
Color/code	Visual	---	Gray
Appearance	Visual	---	Paste
Extrusion rate	/	15 g/s, 0.4 Mpa	90-130
Density	GB/T 15223-1994	25℃, g/cm3	1.65±0.05
Tack-free Time	GB/T13477.5-2002	25℃, 55%RH,min	5-20
After cured
Hardness	GB/T 531.1-2008	Shore A	70±5
Thermal conductivity	GB/T 10297-2015	W/m.K	≥0.75
Elongation at break	GB/T 528-2009	%	≥70%
Tensile strength	GB/T 528-2009	Mpa	≥2
Dielectric strength	GB/T 1695-2005	kV/mm (25 ° C)	20
Loss factor	GB/T 1693-2007	(1MHz) (25℃)	0.09
Dielectric constant	GB/T 1693-2007	(1MHz) (25℃)	2.9
Volume Resistance	GB/T 1692-2008	(DC500V) Ω· cm	≥1.0*1014

All the above data were determined or further experimental tested after 7 days of adhesive curing at 25℃, 55%RH.

Operation process

Surface treatment: will be sticky or coated surface finish clean, clean with cleaning agent to remove rust, dust and oil. Can be applied to a variety of materials, such as glass, metal and most commonly used industrial plastics, to achieve a bottomless coating bond. However, on some polymers, the bond may be poor, such as polyethylene, polypropylene and PTFE. It is recommended to use MAXTECH PM1263 for primer in advance to obtain a good bonding effect.

Sizing: Cut the nozzle to the required size and load it into the glue gun. Squeeze the glue solution onto the cleaned surface for an even distribution. When bonding, the adhesive surface can be closed and fixed. At room temperature and 55% relative humidity, the adhesive exposed to the air will complete the "crust" in about 5 minutes, the surface drying time of 10 minutes, and the curing in 1-2 days according to the application.

Solidification: After completing the crust, the curing will continue from the inside out. The curing depth within 24 hours (room temperature 25 ° C, 50% relative humidity) is approximately 4mm. Very deep sections, especially those with difficulty in contact with water vapor in the air, will require longer curing times. The lower the relative humidity will extend the curing time. The painted part is placed in the air and can be put into use after curing at room temperature for 24 hours.

Note: After opening, use it as much as possible once, once not used up, and then use it again, after squeezing out the cured part, continue to use without affecting normal use.

Please consult MAXTECH Marketing Department for the use of dispensing equipment.
Power, solar energy, equipment, home, automotive, LED lighting,

Power supply, ECU module, semiconductor, high power transistor, thyristor diode
Packaging Specifications

SI 7336G-1TC Grey Silicone Adhesive,

Order code :1KSI3440

300ML/ PCS, 25 PCS/box

2600ML/ PCS, 6 PCS/box

Storage and shipping

Store away from light and heat and in tight seal.

This product is non-dangerous goods, transported and stored as general chemicals.

The storage period is 12 months at 25℃. After the storage period, please take a sample for testing.

Precautions

Keep away from children for storage.

It is recommended to use in a well-ventilated area.

If it gets on the skin, wash it immediately with soapy water.

If it gets on your eyes, rinse immediately with water for a long time and keep your eyes open. If irritation persists, seek medical attention.

SI 7336G-1TC Power supply, ECU module LED grey silicone adhesive

∎Technical Data Table

∎Directions for Use

Usage

∎Transport &Storage